Bay Builders Designs / field guide

Measure clearly. Plan the work. Build with care.

A practical starting point for homeowners and builders: square a layout, estimate materials from measured surfaces, and understand the steps and checks involved in traditional plaster repair or a new window opening.

Start with the layout

01 / Set out the footprint

Square a structure with a 3–4–5 check.

A right triangle gives you a reliable way to set a square corner before you extend the walls or foundation lines.

  1. 01

    Stretch a baseline along one side and mark the first corner A.

  2. 02

    Measure 3 ft from A along the baseline and mark point B.

  3. 03

    From A, measure roughly perpendicular to the baseline and mark point C about 4 ft away.

  4. 04

    Measure from B to C. Adjust C until that diagonal is 5 ft, then secure the lines.

  5. 05

    Extend the sides to the planned lengths. Check that opposite sides are parallel and the footprint matches the plan.

Need a larger check?

Use the same ratio at a larger scale: 6–8–10 ft or 9–12–15 ft. Longer marks make small measuring errors easier to see, if you have room to lay them out.

Verify a rectangle with its diagonals

Measure from one corner to the far opposite corner, then measure the other diagonal. A rectangle is square when both diagonal measurements match, allowing for the accuracy of your tape and layout lines. For a 12 ft by 10 ft footprint, each diagonal should be about √(12² + 10²) = √244 = 15.62 ft, or roughly 15 ft 7.4 in.

A right angle checked with a 3-4-5 triangleA right triangle with a three-foot baseline, a four-foot perpendicular side, and a five-foot diagonal between their ends.3 ft4 ft5 ft
Keep the tape tight and read from the same side of each mark. The 3–4–5 lengths make a right angle because 3² + 4² = 5².

02 / Measure surfaces

Calculate square footage with matching units.

Measure in feet before multiplying. If a tape reading is in inches, convert it to feet first: 6 inches is 0.5 ft, and 9 inches is 0.75 ft.

Floor or ceiling

length × width

A 12 ft by 10 ft floor is 12 × 10 = 120 sq ft.

Four walls

perimeter × height

For a 12 ft by 10 ft room, the perimeter is 2 × (12 + 10) = 44 ft. At 8 ft tall, gross wall area is 44 × 8 = 352 sq ft.

For a material takeoff, subtract large openings from gross wall area when the material will not cover them. Measure sloped or irregular surfaces as smaller shapes and add their areas together.

03 / Turn measurements into a takeoff

Estimate first. Confirm stock and details before ordering.

A takeoff is a planning estimate, not a universal shopping list. Use dimensions from the actual job, select a real product size, add a clear waste allowance, and round up to full sheets, pieces, rolls, or packages.

  1. 01

    Measure the work

    Record lengths, heights, thicknesses, and the face or side being covered.

  2. 02

    Subtract openings

    Remove doors and windows from surface-area materials where they leave no coverage.

  3. 03

    Add an allowance

    Choose a stated waste amount for cuts, breakage, and layout. The sample below uses 10%.

  4. 04

    Round to stock

    Divide by sheet or package coverage, then round up to a usable purchase unit.

Coverage varies by product, thickness, installation method, and local requirements. Check the package label, manufacturer instructions, and project plan before buying.

04 / Worked example · illustrative only

A 12 ft × 10 ft structure with one window and one door.

Assume 8 ft high walls, drywall on the interior face only, one 3 ft × 4 ft window, one 3 ft × 6 ft 8 in door, and a 10% waste allowance. The floor is 120 sq ft, but this takeoff covers walls only. The drawing shows one 12 ft wall; the door is on a 10 ft wall. For the framing allowance, assume the window rough opening is 38 in × 50 in with its sill 30 in above the bottom of the wall, and the door rough opening is 38 in × 82 in. Confirm each rough opening against the actual manufacturer instructions.

Illustrative twelve-foot by eight-foot wallA twelve-foot-long, eight-foot-high framed wall with a three-by-four-foot window; the companion door is on a separate ten-foot wall.12 ft8 ft3 × 4 ft12 ft wall · window shown; door is on the 10 ft wall
The window is shown on a 12 ft wall; the door is on a 10 ft wall and is not shown. Unit sizes are used for the area calculation. Confirm framing rough openings for the products used.

1. Find the net wall area

Gross: 2 × (12 + 10) ft × 8 ft = 352 sq ft

Window: 3 ft × 4 ft = 12 sq ft

Door: 3 ft × 6 ft 8 in = 3 × 6⅔ ft = 20 sq ft

Net: 352 − 12 − 20 = 320 sq ft

With 10%: 320 × 1.10 = 352 sq ft

2. Estimate surface materials

Drywall sheets
4 ft × 8 ft = 32 sq ft each. 352 ÷ 32 = 11, so buy 11 sheets.
Insulation batts
Assume each 15 in × 93 in batt covers 9.69 sq ft: 15 ÷ 12 × 93 ÷ 12 = 9.69. 352 ÷ 9.69 = 36.3, so buy 37 batts.
Joint tape
Assume about 96 ft for vertical sheet seams and four inside corners. Add 10%: 105.6 ft. One assumed 250 ft roll covers this estimate.
Joint compound
If the chosen 4.5 gal pail label lists 450 sq ft coverage, 352 ÷ 450 = 0.78; buy 1 pail. Use the selected product’s actual label.
Drywall screws
Budget 40 per sheet: 11 × 40 × 1.10 = 484. One assumed 500-count box is enough; confirm fastener type and spacing for the board and framing.

3. Rough-count the framing stock

Three plate runs around the 44 ft perimeter total 44 × 3 = 132 linear ft. Add 10% for cuts: 145.2 linear ft. With assumed 2×4×12 ft stock, 145.2 ÷ 12 = 12.1, so allow 13 boards.

At 16 in on-center, the two 12 ft walls need 2 × 10 positions = 20, and the two 10 ft walls need 2 × 9 positions = 18: 38 full-height positions. For this rough example, two positions at each opening are replaced by four king studs, leaving 38 full-height pieces; allow four jack pieces. Add 10% to those 42 stock pieces: 46.2, rounded up to 47 2×4×8 ft boards. For a piece-count example, assume a 5.5 in header depth only to estimate the short cripples; the header itself still needs a structural design. The two window cripples below the sill are about 28.5 in each; the two above the header are about 7 in each; and the two above the door are about 5 in each. Those six cripples total about 81 in. Add the 38 in sill and 10%: (81 + 38) × 1.10 = 130.9 in, which rounds up to two more 2×4×8 ft boards. Total: 49 assumed 2×4×8 ft boards for studs, jacks, cripples, and sill.

Header stock is excluded from this count. Its size depends on span, loads, wall assembly, and local code; get the required design before ordering or cutting.

These quantities are examples, not exact counts for every room. A different sheet layout, framing layout, product label, damaged stock, ceiling, second drywall face, or opening detail changes the takeoff. Verify on site and round each package to a full purchase unit.

05 / Traditional wall repair

Lath first, then scratch, brown, and finish coats.

Traditional three-coat plaster depends on a stable base and the chosen lath and plaster system. Product thicknesses, lath spacing, mixes, and curing times vary; follow the system instructions and local requirements.

  1. 01

    Inspect and prepare the base

    Find and correct moisture or movement first. Remove only material confirmed safe to disturb. Expose sound framing or a sound existing base, and plan a clean edge for the patch.

  2. 02

    Install or repair the lath

    Fasten compatible wood or metal lath securely to the support. Follow the plaster system for lath direction, fasteners, joints, and gaps; the openings must let the base coat form a mechanical key without leaving unsupported edges.

  3. 03

    Apply the scratch coat

    Press the base coat through the lath so it keys behind the strips or mesh. Bring it to the system thickness, then scratch horizontal grooves while it is still workable to give the next coat a grip.

  4. 04

    Apply the brown coat

    After the scratch coat has firmed or cured as specified, apply the leveling coat. Fill low areas and rule or float the surface flat and plumb, leaving the texture required for the finish coat.

  5. 05

    Apply the finish coat

    When the brown coat is ready, apply the thin finish coat and work it to the required smooth or textured finish. Protect each coat from drying too quickly and allow the specified cure before painting or decorating.

06 / Plan before you cut

Adding a window is a structure and water-management project.

Window details depend on the wall assembly, window type, cladding, and existing water barrier. Use this sequence to plan the work; the installation detail must match the wall assembly.

Before any cutting

Check permits and local code, identify electrical, plumbing, gas, and other services in the wall, and establish whether it carries structural loads. Have qualified professionals assess utilities and structural changes. Do not cut until those checks are complete and the opening design is approved where required.

  1. 01

    Choose and plan the opening

    Confirm the window type and manufacturer’s rough-opening dimensions. Check its location from inside and outside, including wiring, plumbing, exterior trim, drainage, egress, safety glazing, energy, and any permit requirements that apply locally.

  2. 02

    Expose and frame the rough opening

    After utility and structural checks, remove interior and exterior finishes carefully enough to inspect the wall. Support or shore the structure when the approved design requires it. Form the sill, jambs, and header to the approved dimensions, fastening them as specified; keep the opening square and protect it from rain while work is underway.

  3. 03

    Prepare the water-control layer

    Identify the existing building paper, housewrap, taped sheathing, liquid-applied barrier, or other weather-resistive barrier (WRB). Prepare a compatible sill pan or sill flashing and connect it to that drainage layer so water can escape to the exterior.

  4. 04

    Set and flash the window

    Set the unit plumb, level, and square; shim and fasten it using the window instructions. Install compatible side and head flashing in the sequence for that wall assembly. In many drained-wall details, sill flashing comes first, side flashing laps over it, and head flashing laps over the sides; integrate the WRB above so water sheds outward.

  5. 05

    Reconnect the exterior finish and repair inside

    Reconnect building paper, housewrap, or the selected WRB to the flashing, then restore the exterior finish and trim without blocking drainage paths or window weeps. Air-seal and insulate the interior gap as specified. Repair interior lath and plaster as a separate finish task after the exterior is weather-tight.

Exterior / weatherproofing

Flashing, the window, the WRB, and the exterior finish must work together to direct water out. Follow the chosen window and flashing instructions for this assembly.

Interior / lath-and-plaster repair

Interior lath, plaster coats, insulation, and air sealing repair the inside finish and cavity. They do not replace exterior flashing or WRB integration.

Follow local code and the window manufacturer’s instructions. Where the wall is load-bearing or structural framing must change, get a qualified design and qualified help before work begins. A building-science overview of fully flashed openings is available from the U.S. Department of Energy’s Building Science Education resource.

07 / Keep water moving out

Waterproofing Guide

Roofs, openings, above-grade walls, and foundations are different assemblies. There is no single waterproofing order that applies to all of them. These are typical planning sequences, not construction documents: project details depend on the design, the selected products, the site, and local requirements.

Assembly 01

Roofs

Illustrative sequence for a pitched roof with asphalt shingles. Low-slope membrane roofs, metal roofs, and other coverings use different details.

  1. Confirm the roof design, covering instructions, slope range, and local requirements. Start with sound, dry sheathing; repair soft or damaged areas and plan valleys, edges, and every penetration.

  2. Build the eave-to-rake edge detail. Place drip edge and any specified self-adhered ice-and-water membrane in the order required by the roof design and local code. A common shingle detail puts eave drip edge below the underlayment and rake drip edge above it. Lap the underlayment from low to high so water sheds outward.

  3. Flash valleys, pipes, skylights, and roof-to-wall joints with the components made for the roof system. Integrate step flashing course by course with the shingles; use kick-out flashing where a roof edge meets a wall so concentrated water is sent away from the wall.

  4. Install the starter course and shingles from the eaves upward, following the required exposure and fastening pattern. Keep each shingle course and flashing lap draining over the one below it, then finish ridges and hips with the specified cap detail.

  5. Use compatible roofing sealant only at exposed joints or fasteners where the product detail calls for it. Caulk is a supplemental seal at specific locations; it does not replace underlayment, membrane, or properly layered flashing.

Assembly 02

Windows and doors

A common drained-wall approach for flanged windows and doors; unflanged units, thresholds, and wall systems need their own compatible details.

  1. Choose the unit and installation detail for the wall’s water-resistive barrier (WRB), cladding, and framing. Check the rough opening and prepare a sound sill with the outward drainage slope required by the design.

  2. Form a sill pan with compatible preformed, fluid-applied, or self-adhered flashing membrane. Seal its corners and end dams as specified, and connect its outer edge to drain over the WRB; do not create a sealed pocket that traps water.

  3. Set the window or door plumb, level, and square, then shim and fasten it as its manufacturer directs. Keep designed drainage openings and window weeps clear.

  4. Install compatible jamb flashing and then head flashing in the sequence for that unit. In a common flange detail, jamb flashing covers the sides, head flashing protects the top, and the WRB flap above laps over the head flashing so water drains to the exterior.

  5. Apply sealant at the frame or flange only where the unit and wall details require it; preserve the sill’s drainage route. Air-seal the interior perimeter separately as specified. Caulk does not replace the sill pan, flashing membrane, or WRB connection.

Assembly 03

Walls

This sequence describes a typical drained wall with a WRB behind the cladding. Barrier, masonry, and other wall systems may manage water differently.

  1. Plan a continuous water-control plane behind the cladding and a path for water to drain out. Confirm the sheathing is sound and the cladding system allows the drainage or ventilation space required by its design.

  2. Install the specified sheet or fluid-applied WRB or membrane over the prepared wall. Lap joints in shingle fashion, generally working upward from the base, and follow the product instructions for seams, corners, and fasteners.

  3. Connect flashing to the WRB at window and door heads, wall bases, roof-to-wall intersections, decks, and other penetrations. Flashing should direct water back to the exterior; lap upper layers over lower ones and include kick-out flashing where roof runoff would otherwise hit the wall.

  4. Install any specified drainage mat or rainscreen gap, then the cladding and trim. Keep base flashing, weeps, and other designed exits open so incidental water can drain rather than collect behind the finish.

  5. Use compatible caulk with backer rod only at designed exposed movement joints or transitions. Do not caulk over weeps or seal every lower edge shut; sealant is not a substitute for the wall membrane and flashing network.

Assembly 04

Foundations

Below-grade protection depends on soil, groundwater, foundation type, and drainage conditions. A high-water-table or complex site needs project-specific design.

  1. Plan surface-water control and below-grade drainage together. Direct roof runoff away, finish the site to drain away from the building where the site allows, and determine whether the design needs damp-proofing, waterproofing, a footing drain, under-slab drainage, or a sump.

  2. Before excavation, have underground utilities located and identify nearby structures and soil conditions. Use a competent person to select and inspect the required protective system; never enter an unprotected excavation or trench.

  3. Prepare the concrete or masonry as the selected system requires, including joints, cracks, penetrations, and footing-to-wall transitions. Apply a compatible below-grade waterproofing membrane continuously over the designed area; at the above-grade transition, connect the wall WRB to the base flashing or drainage detail so water can exit.

  4. Install the specified protection or drainage layer without damaging the membrane. Place and connect the footing drain at the designed elevation, with the specified filter material, cleanouts, and approved outlet or sump; coordinate the exact order with the waterproofing and drain products.

  5. Inspect the membrane and drainage connections before backfilling. Backfill with the specified material without puncturing the protection layer, then complete grading and downspout discharge so surface water is carried away.

  6. Use only compatible sealant at joints or service penetrations where the membrane system specifies it. Caulk alone is not a below-grade waterproofing system and cannot replace the designed membrane and drainage; flashing is generally used at the above-grade wall transition, not as the buried wall membrane.

Before work starts, confirm the assembly with the project designer or a qualified building professional, read the exact product instructions, and check permits and local requirements. Stop if existing water damage, unsafe access, or unexpected site conditions change the planned detail.

Reference desk

Check the conditions that apply to your project.

Next / back to plan questions

Review checkout, downloads, and other plan details in the FAQ.

Return to the plan buyer FAQ